Reset image position
Close
Back
Item no. 90291
34 in stock
pcs.
SVB price: €159.62
You save: 8%
€173.88
Excl. VAT, excl. shipping costs.
This is a NET-price excluding German VAT. Shipments to countries outside of the EU may be subject to import duties and taxes.
pcs.
€159.62 This is a NET-price excluding German VAT. Shipments to countries outside of the EU may be subject to import duties and taxes.
Buy
Available variants:
Image of SeaTalkNG to NMEA0183 Converter

YACHT DEVICES SeaTalkNG to NMEA0183 Converter

This bidirectional converter allows you to easily connect your NMEA0183 devices to your SeaTalkNG network and vice versa. Support for many data outputs, such as: AIS, waypoints, routes and autopilot. 

Item no.
90291
EAN
4779045210274
Model no.
YDNG-03N
Description
Yacht Devices - NMEA2000 to NMEA0183 converter

SVB recommends the following for this item

Product details

This bidirectional converter allows you to easily connect your NMEA0183 devices to your NMEA2000 network and vice versa. Support for many data outputs, such as: AIS, waypoints, routes and autopilot.
Baud rate is configurable from 300 to 115,200 baud for NMEA0183 connection and also allows you to easily use AIS transponders (38,400 baud) and PC adapters, in addition to the standard NMEA0183 devices. The default baud rate is 4,800 baud. It is not possible to define a separate baud rate for the input or output, the defined baud rate is set for the input & output in parallel.

The device can be configured and firmware updates downloaded using a microSD card slot. No special software is needed for this! Only a device (laptop, PC, smartphone), a microSD reader and a text editor are required.
During configuration, you can, for example, change the baud rate for AIS data to 38,400, 9,600 baud for Navtex data or for faster data transmission to up to 115,200 baud. Filters can also be set to block data sets that should not be rendered. There is a blacklist (block before rendering) and a whitelist function (only render these data sets).

Instructions for changing the baud rate:
  1. Insert an empty Micro-SD card into the corresponding card slot of your computer.
  2. Next step is to create a text file (TXT) and save it on the Micro-SD card. Do this as follows:
  3. Open the editor. Depending on the Windows version, this can be carried out via the Start menu -> Windows Accessories.
  4. Now enter the following line in the editor:

    0183_SPEED=x

    Where the x represents the respective baud rate.

    For configuration with 4800 baud (e.g. for GPS, wind, depth or compass data) the command is as follows:
    0183_SPEED=4800

    For configuration with 38400 baud (e.g. for AIS data) the command is as follows:
    0183_SPEED=38400
  5. Now save the text file via "File -> Save" under the following names on the Micro-SD card
    YDNG.TXT
  6. Remove the Micro-SD card from the card slot of your computer and insert it into the Yacht Devices Converter. You can now use the Converter with the baud rate you have set.

Note: a second colour scheme has been used by the manufacturer since 2024. Unfortunately, the current scheme is still indicated on the housing label of the device. The old colour scheme #1 is used in the manual.

The conversion is as follows:
NMEA0183 Signal RX+ (IN A) RX- (IN B) TX+ (OUT A) TX- (OUT B) GROUND
Colour scheme #1 YELLOW BLUE RED BLACK CLEAR
Colour scheme #2 YELLOW GREEN WHITE BROWN GREY

Technical specifications:
  • Connection: NMEA2000 Micro-C
  • Current consumption via the NMEA2000 network: 30 mA
  • Voltage range: 7-16 V
  • Cable length: 400 mm
  • Housing length without connections: 54 mm

Documents

en-flag Manual
PDF, 1,81 MB
de-flag Manual
PDF, 2,23 MB

What other SVB customers have to say

100% real reviews

4 customer reviews

4.8 (out of 4 ratings)
3 Stars
(0)
2 Stars
(0)
1 Stars
(0)
Wilfried S.
by Wilfried S. Flag of Germany 2/3/2020 Verified purchase
Gut aber teuer!
Good product, very good advice, but the price is a bit excessive.
View all ratings

Rate product

How would you rate this product?
Disappointed
Completely fails to meet my expectations
Poor
Only some expectations are met
OK
Meets my basic expectations
Good
Slightly better than my general expectations
Excellent
Fully exceeds my expectations
Click on the stars to rate

Customers ask customers

Ask other SVB customers who have already purchased this product from us about their experience.

Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .

  • More "Customers ask customers" available in the following languages :
  • Flag of Deutsch

Technical question

Question:
User image of Willem R.
Willem R. asked
on Feb 14, 2024
Flag of English Can I use the yacht device nmea 2000 to 0183 to connect my vulvan to my autohelm instruments st50 wind & log and st4000+autopilot? Can I use the yacht device to connect my vulcan to my ICm505 ? Regards
Answer:
SVB expert image
Andrew C. answered
on Feb 14, 2024
Unfortunately, ST50 Wind instruments have no NMEA0183 interface ( only ST50+ TRIDATA REPEATER has it). I recommend to use YDNR-02 - it has Seatalk1 interface (so ST50 can be connected), and two 0183 bidirectional ports, where you can connect ST4000 and Icom505. Also it has WiFi interface, so you can control autopilot from your tablet or any marine application (like OpenCPN).