VICTRON MultiPlus Inverter / Charger 12 V / 1300 W / 70 A
VICTRON MultiPlus Inverter / Charger 12 V / 700 W / 35 A
This device combines a powerful sine wave inverter, state-of-the-art battery charger using VICTRON's 4-stage adaptive charging technology and a high-speed AC source transfer switch in a compact housing. The unit is further characterised by its proven reliability,...
VICTRON MultiPlus Inverter / Charger 12 V / 1000 W / 50 A
This device combines a powerful sine wave inverter, state-of-the-art battery charger using VICTRON's 4-stage adaptive charging technology and a high-speed AC source transfer switch in a compact housing. The unit is further characterised by its proven reliability,...
VICTRON MultiPlus Inverter / Charger 12 V / 430 W / 20 A
This device combines a powerful sine wave inverter, state-of-the-art battery charger using VICTRON's 4-stage adaptive charging technology and a high-speed AC source transfer switch in a compact housing. The unit is further characterised by its proven reliability,...
VICTRON MultiPlus Inverter / Charger 12 V / 1600 W / 80 A
This device combines a powerful sine wave inverter, state-of-the-art battery charger using VICTRON's 4-stage adaptive charging technology and a high-speed AC source transfer switch in a compact housing. The unit is further characterised by its proven reliability,...
SVB recommends the following for this item
Product details
Fully automatic and high load capacities
If the shore power or on-board generator is interrupted, the MultiPlus inverter then automatically takes over the supply of connected consumers in less than 20 milliseconds.
Peak power is often required for a limited period only. In such cases, the MultiPlus automatically compensates for insufficient shore power or generator output with energy from the battery. If the load is reduced, i.e.. when consumers are switched off, the energy that is then available again can be used to charge the batteries.
Thanks to the high short-term load capacity, consumers with high inrush currents, such as LED lights, halogen bulbs or power tools, can also be operated.
Optimal charging of starter and consumer batteries
The MulitPlus has two DC outputs for charging starter and consumer batteries. The 4-stage charging characteristic always ensures optimum charging and can be adjusted to different battery types by means of DIP switches.
Intelligent search mode
When search mode is activated, power consumption of the inverter is reduced by about 70% at no load operation. In this mode, the inverter shuts down at low load and turns on again every two seconds for a short period. If the output current of a set limit is exceeded, the inverter immediately switches on again. If this is not the case, the inverter switches itself off again.
Integrated multifunction relay
The MultiPlus also has a programmable multi-function relay, which works as an alarm relay in the default setting. This relay can also be reprogrammed for other functions, e.g. as a start relay for a generator.
System with shore connection
The Multiplus charger / inverter combo acts as a UPS (uninterruptible power supply) to provide power in the event of an input power source failure.
System with shore connection and DC generator
In this system example, the generator charges the batteries directly or feeds the inverter.
Technical specifications
Inverter
Input voltage range | 9.5 - 17 V |
Output voltage | 230 V AC |
Frequency | 50 Hz |
Continuous output power | 1600 VA |
Peak performance | 2800 W |
Max. Efficiency | 93% |
Zero-load power | 10 W |
Zero-load power in search mode | 3 W |
Charger
AC input | 187 - 265 V AC |
Frequency | 45 - 65 Hz |
Charge voltage 'absorption' | 14.4 V |
Charge voltage 'float' | 13.8 V |
Storage mode | 13.2 V |
Charging current | 70 A |
Battery temperature sensor | Yes |
General
Protection | a - g |
Operating temperature range | -40 to +65 °C |
Material | Steel / ABS |
Protection category | IP21 |
230 V connection | G-ST18i connector |
Battery connection | 50 mm² |
Dimensions (WxHxD) | 265 x 470 x 120 mm |
Weight: | 10.2 kg |
Notes
- A battery temperature sensor is included in the delivery contents. This is insulated and glued into a 10 mm ring cable lug and is attached directly to a battery terminal.
Do not use the sensor in conjunction with LiFePO4 batteries. - Also included are coupling and plug (type GST18) for the AC-INPUT and AC-OUTPUT connection. These come plugged together in the box and are may not immediately be recognised as couplings and plugs when they are unpacked.
Documents
Accessories
Customers also bought
Similar items
Comparison with other products
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .