SET: MARE FLEX 120W with WMarine 10 Charging Regulator, Fuse and Holder / 120 W
Available variants:
Item no.
25848
Description
SET: MARE FLEX (120W) with MPPT WMarine 10 charging regulator, fuse holder and 15 A fuse
Construction type
Semi-flexible
Nominal Power @ 12 V
120
W
max. Power Current (Imp)
6
A
max. Power Voltage (Ump)
20
V
Short circuit current (Isc)
6.48
A
Open circuit voltage (Uoc)
23.5
V
Connector
None
Attachment
Adhesive, Loops
Module connection
Front side
Connector cable
Round (multi-core)
Walkable
No
Length
1.19
m
Width
54
cm
Height
4
mm
SVB recommends the following for this item
Product details
The thin and light MARE FLEX 120 solar module delivers a maximum output of 120 Wp, is bendable and perfect for installing on sailing yachts and motor boats as well as on the roofs of caravans and trucks. It is also ideal for use in mobile applications, such as outdoor activities and camping. The front and back foil is made of ETFE and is weatherproof, yet extremely translucent. The module is particularly easy to install: It can either be fixed in place with construction adhesives (e.g. SIKA 291) or by using the integrated stainless steel eyelets. The solar module is supplied with a 5 m long connection cable with 2 x 2.5 mm² cable heads.
Advantages of the MARE FLEX 120 module
Technical data
MPPT Western WMarine 10 Charge regulator
Thanks to its buck-boost MPPT technology, the WESTERN WMarine10 is an ideal charge regulator for small 12/24 volt marine / caravan or off-grid applications. Suitable for lead/acid, AGM, gel and LiFePO4 batteries. High-quality workmanship, quick installation, simple 2-button operation, intuitively clear display, programmable day/night detection and overload protection on consumer output, just some of the highlights of this unique charging regulator!
The outstanding feature of the Wmarine 10 Buck-Boost MPPT regulator* is its ability to transform even very low module voltages below the battery voltage to the required battery charging voltage thanks to its integrated DC/DC converter. Other regulators only become active when the module voltage is a few volts above the battery voltage. The WMarine10 starts at 5 volts and is suitable for module voltages up to max. 40 Voc!
This is particularly interesting for partially shaded 12 V modules, as the module output voltage is too low for the usual downward regulators despite the module bypass diodes that may be present. The Wmarine 10 also performs well in transitional periods with low sunlight and poor lighting conditions, as well as when solar modules are operated in climatically hot environments, as output voltage is known to decrease with increased module temperature.
The WMarine10 is suitable for charging all types of lead/acid batteries (maintainable/maintenance-free with liquid acid, AGM and GEL) as well as LiFePO4 batteries. It has a charging output/battery connection. When it is connected to the battery, it automatically detects whether a 12 V or 24 V battery is being used.
An external temperature sensor with 2 m connection cable (included in delivery) monitors the battery temperature and ensures a temperature-compensated charging voltage (24 mV/°C). Thanks to a 2-pole screw-plug connection, the sensor can be easily connected to the controller. The small sensor itself is isolated and can be attached to the side of the upper third of the battery housing with insulating tape or directly to a pole terminal and fastened there with cable ties. A sensor that is not connected or a connection cable break is shown "-32°C" in the display.
The few necessary basic settings as well as switching to the different input and output display values (voltage, current, power, temperature) is done with 2 large keys (1 cm Ø).
The values are shown on a 46 x 28 mm LC display with clearly visible symbols, as well as text and numerical values.
The regulator has a programmable consumer output connection with 5 switching options for load currents up to 15 amps with overload and deep discharge protection. The consumer output connection can also be used in combination with the regulator's adjustable day/night detection. Switch-off and switch-on voltages can also be set. On a boat, the consumer output can be used, for example, for an anchor light or a cooler box (without battery deep discharge protection) in the caravan as a programmable night/orientation light, etc.
The WMarine 10 is quiet and efficient. There is no need for a fan for the small amount of heat generated during use. The solid aluminium housing is completely sufficient for this. There is enough space for the sophisticated electronics, for the 2-pole screw/plug connection of the temperature sensor and for the solid screw terminals, which can easily accommodate cable cross-sections of up to 10 mm². Housing dimensions: 160 x 135 x 50 mm, weight 515 g. The housing has four 4.5 mm drill holes for mounting, drill hole spacing: 149 x 125 mm.
Features at a glance
Technical data
Includes ATO In-Line Fuse Holder and 15 A-fuse
Waterproof in-line fuse holder for ATO® fuses. Supplied with connection cable (cross-section: 3.1 mm²). Suitable for max. 30 A fuse Amperage. 15 A fuse included. WEIGHT: 0:09 kg.
Installation instructions
Advantages of the MARE FLEX 120 module
- Higher output
- Flexible, rugged and durable
- Easy and cost-effective installation
- Long connection cable
Technical data
Type | MARE FLEX 120 |
Nominal power (Pnom) | 120 Wp |
Nominal voltage (Vmpp) | 20 V |
Nominal current (Impp) | 6 A |
Open circuit voltage (Voc) | 23.5 V |
Short circuit current (Isc) | 6.48 A |
Max. System voltage | 70 V |
Module connection cable | 2x 2.5 mm², Length: 5000 mm |
Eyelet material | Stainless steel 316 |
Weight: | 4.6 kg |
Dimensions | 1190 x 540 x 4/19* mm *without/with connection box |
MPPT Western WMarine 10 Charge regulator
Thanks to its buck-boost MPPT technology, the WESTERN WMarine10 is an ideal charge regulator for small 12/24 volt marine / caravan or off-grid applications. Suitable for lead/acid, AGM, gel and LiFePO4 batteries. High-quality workmanship, quick installation, simple 2-button operation, intuitively clear display, programmable day/night detection and overload protection on consumer output, just some of the highlights of this unique charging regulator!
The outstanding feature of the Wmarine 10 Buck-Boost MPPT regulator* is its ability to transform even very low module voltages below the battery voltage to the required battery charging voltage thanks to its integrated DC/DC converter. Other regulators only become active when the module voltage is a few volts above the battery voltage. The WMarine10 starts at 5 volts and is suitable for module voltages up to max. 40 Voc!
This is particularly interesting for partially shaded 12 V modules, as the module output voltage is too low for the usual downward regulators despite the module bypass diodes that may be present. The Wmarine 10 also performs well in transitional periods with low sunlight and poor lighting conditions, as well as when solar modules are operated in climatically hot environments, as output voltage is known to decrease with increased module temperature.
The WMarine10 is suitable for charging all types of lead/acid batteries (maintainable/maintenance-free with liquid acid, AGM and GEL) as well as LiFePO4 batteries. It has a charging output/battery connection. When it is connected to the battery, it automatically detects whether a 12 V or 24 V battery is being used.
An external temperature sensor with 2 m connection cable (included in delivery) monitors the battery temperature and ensures a temperature-compensated charging voltage (24 mV/°C). Thanks to a 2-pole screw-plug connection, the sensor can be easily connected to the controller. The small sensor itself is isolated and can be attached to the side of the upper third of the battery housing with insulating tape or directly to a pole terminal and fastened there with cable ties. A sensor that is not connected or a connection cable break is shown "-32°C" in the display.
The few necessary basic settings as well as switching to the different input and output display values (voltage, current, power, temperature) is done with 2 large keys (1 cm Ø).
The values are shown on a 46 x 28 mm LC display with clearly visible symbols, as well as text and numerical values.
The regulator has a programmable consumer output connection with 5 switching options for load currents up to 15 amps with overload and deep discharge protection. The consumer output connection can also be used in combination with the regulator's adjustable day/night detection. Switch-off and switch-on voltages can also be set. On a boat, the consumer output can be used, for example, for an anchor light or a cooler box (without battery deep discharge protection) in the caravan as a programmable night/orientation light, etc.
The WMarine 10 is quiet and efficient. There is no need for a fan for the small amount of heat generated during use. The solid aluminium housing is completely sufficient for this. There is enough space for the sophisticated electronics, for the 2-pole screw/plug connection of the temperature sensor and for the solid screw terminals, which can easily accommodate cable cross-sections of up to 10 mm². Housing dimensions: 160 x 135 x 50 mm, weight 515 g. The housing has four 4.5 mm drill holes for mounting, drill hole spacing: 149 x 125 mm.
Features at a glance
- MPPT buck-boost charge regulator for module voltages between 5 and 40 Voc
- Automatic detection of 12 V or 24 V battery voltage at startup
- Maximum module power: 120 Wp for 12V battery and 220 Wp for 24V battery
- One charge output is suitable for maintainable / maintenance-free lead / acid battery types, AGM, GEL and LiFePO4
- Temperature compensated charging voltage thanks to external battery sensor
- 48 LCD displays for input / output values (voltage, current, power), temperature or settings
- Simple 2-button operation
- Backflow-free due to integrated blocking diode
- Consumer connection with 18 programmable functions, max. 15 A load capacity with overload protection and battery deep discharge protection with adjustable switch-off and restart limit
- Over temperature protection
- Reverse polarity protection
- Aluminium metal housing IP20
- 10 mm² connection terminals
Technical data
Battery voltage 12 V | Battery voltage 24 V | ||||||
Min | Type | Max | Min | Type | Max | ||
Battery voltage | Vbatt | 10 V | - | 16 V | 20 V | - | 32 V |
Open circuit voltage of the solar cell | Voc | 5 V | - | 40 V | 5 V | - | 40 V |
Module current | Imp | - | - | 10 A | - | - | 10 A |
Maximum power of the solar cell | Pmp | - | - | 120 W | - | - | 220 W |
Output voltage at the consumer output | Vload | - | Battery voltage | - | - | Battery voltage | - |
Max. consumer output current | Iload | - | - | 15 A | - | - | 15 A |
Consumption | Iq | 12.7 mA (Vbat 14.0 V) |
17.7 mA (Vbat 28.0 V) |
||||
Operating temperature | Tamb | -10 °C | 50 °C | -10 °C | 50 °C | ||
Power loss | Ploss | 20 W | 29 W | ||||
Cross section at the terminals | 1 mm² | 10 mm² | 1 mm² | 10 mm² | |||
Level of protection | IP20 | IP20 | |||||
Weight: | - | 515 g | - | - | 515 g | - |
Includes ATO In-Line Fuse Holder and 15 A-fuse
Waterproof in-line fuse holder for ATO® fuses. Supplied with connection cable (cross-section: 3.1 mm²). Suitable for max. 30 A fuse Amperage. 15 A fuse included. WEIGHT: 0:09 kg.
Installation instructions
- This set includes a semi-flexible solar module. Semi-flexible means that this type of module should not be constantly bent in and out of shape.
If you are not intending to mount the module permanently (glue or screw), i.e. you want to use it as a mobile unit, it is advisable to add reinforcement to the back of the module. This can be done with light, inexpensive 3 or 4 mm thick aluminium sandwich panels (Alubond, Dibond, etc.). Search the Internet for "aluminium sandwich panels custom size".
The module has a 5 m long connection cable with 2 x 2.5 mm² cable heads. - You can use a small scupper together with marine sealant for through-hull protection.
- Keep connection cables to the battery as short as possible and use tin-plated 6 mm² cables. Note: Install a fuse/fuse holder on the POSITIVE wire near the battery.
Use a crimp connector to connect the POSITIVE line to the fuse holder. On the other end of the fuse holder, fit a crimp ring cable terminal that matches the battery pole terminal. Usually you will find threaded bolts or screws with 6, 8 or 10 mm diameter on the pole terminals. - Further mounting material, such as heat shrink tubing, cable ties, etc. can also be found in our range or below in accessories.
Documents
Accessories
Small Scupper
from
€4
16
2 variants
BLUE SEA
Wall Duct / up to 7 mm
only
€17
61
13
-17%
YACHTICON
Multi Purpose Self-welding Tape / black
€9.62
only
€7
98
90
-17%
YACHTICON
Multi Purpose Self-welding tape / white
€9.62
only
€7
98
56
PHAESUN
QUICKCAB4 Module Cable
from
€32
73
6 variants
-46%
Cable Inlet / 1 x PG Gland
€20.13
only
€10
88
> 100
-45%
Cable Seal / 2 x PG Gland
€22.65
only
€12
56
> 100
Cable Ties
from
€4
16
11 variants
Adhesive Cable Tie Mounts
from
€4
16
2 variants
TIKAL
TIKALFLEX Contact 12 Adhesive / Sealant
from
€5
84
5 variants
Installation Conduit
from
€0
84
4 variants
Customers also bought
SIKA
Sikaflex - 291i Marine Sealant / Filler
from
€7
14
6 variants
Ring Cable Terminal / red / 0.5 - 1.5 mm² / pack of 25
from
€2
86
2 variants
NASA MARINE
Clipper Battery Monitor BM-1
only
€142
82
10
Wood Thru-Hull Plugs / Ø 10-40 mm
only
€6
68
> 100
NV VERLAG
NV Atlas DE12: The Weser, Bremen to Helgoland and Jade
only
€60
75
61
NV VERLAG
NV Atlas DE13: Eastern Frisian Islands, Borkum to Helgoland and River Ems
only
€60
75
55
VETUS
Filter Element for Odor Filter
only
€21
43
> 100
Similar items
SET: Tough Flush Solar Panel 111 W including MPPT Moonray160 Charge Regulator, Fuse and Holder
only
€546
18
3
-9%
PHAESUN
Solar Module Kit 12 V / 12 W
€53.70
only
€48
70
11
SET: SPR-120 incl. WMarine 10 Charging Regulator, Fuse and Holder / 120 W
only
€420
13
9
Solar Starter Set: Nordic 54 W Module
only
€210
04
4
Comparison with other products
1
This product
2
Item no.
25848
25849
Customer ratings
Description
SET: MARE FLEX (120W) with MPPT WMarine 10 charging regulator, fuse holder and 15 A fuse
SET: SPR-120 incl. MPPT WMarine 10 charging regulator, fuse holder and fuse
Width
54 cm
52.7 cm
Height
4 mm
35 mm
Attachment
Adhesive, Loops
Adhesive
Length
1.19 m
103.7 cm
Connector
None
Standard-4 (MC-4)
Construction type
Semi-flexible
Framed module
Module connection
Front side
Rear side
Connector cable
Round (multi-core)
2 single cables
Open circuit voltage (Uoc)
23.5 V
24.1 V
Short circuit current (Isc)
6.48 A
6.46 A
max. Power Voltage (Ump)
20 V
20.1 V
max. Power Current (Imp)
6 A
5.98 A
Availability / Price
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .
No questions asked yet. Be the first to ask a question!