SEATEC SPRINT PRO Hard Antifouling
Item no.
66680
EAN
5035686881839
Model no.
66680
Description
SEATEC - Antifouling SPRINT PRO
Antifouling type
Hard antifouling
Area of application
Salt water, Fresh water, Brackish water / Mixed operation
Hull material
GRP, Wood, Steel
Method of application
Roller, Brush, Spray gun
Biocide-free
No
Immersion after
12
h @ 15 °C
Max. time before immersion
6 months
Yield (theoretical)
7.5
m²
BAuA-No.
N-74278
Boat type
Sailboat, Motorboat
No. of coats (recommended)
2 - 3
Existing coating
SEATEC Sprint Pro, INTERNATIONAL Ultra 300, HEMPEL Hard Racing TecCel, HEMPEL Ecopower Racing, BOERO Altura 619 Plus, BOERO Scirocco 622, AWN Hart Antifouling
For the Netherlands
No
SVB recommends the following for these items
Product details
Highly effective, general purpose hard antifouling for sailing yachts, dinghies, motor yachts, as well as fast motor boats in areas with medium fouling conditions. It is suitable for use in fresh, salt and brackish waters as well as in the Mediterranean area (exception: SPRINT PRO Dover White) and can be applied to GRP, steel and wood. Drying time approx. 1-2 hours. The antifouling can be applied up to 3 months before launching. Thinner: Antifouling Thinner. Yield: 10 m²/l.
Processing instructions
Technical specifications
Processing instructions
Technical specifications
- Processing temperature: +5° C to +35° C
- Drying time at 15 °C: 45 minutes (dust dry)
- Overcoating time at 15 °C: min. 10 hours
For coated surfaces:
- In good condition: Remove fouling, impurities and paint residues completely and then sand wet with 80-120 grit sandpaper (not dry!). If existing antifouling is not compatible or unknown, seal with suitable barrier coat.
- In poor condition: Remove all antifouling residues.
GRP/Blank gelcoat: Make sure the surface is clean, dry, dust-free and in a generally good condition. Then prime the surface with Plasmotec or with Epotec (osmosis protection). Then apply two coats of SPRINT PRO.
Steel/lead/wood: Make sure the surface is clean, dry, dust-free and in a generally good condition. Then prime the surface with Plasmotec or with Epotec to protect the hull from corrosion. Then apply two coats of SPRINT PRO.
Not suitable for use on aluminium.
These antifoulings / paints may not be used in Holland.
Use biocidal products with care. Always read the label and product information prior to use.
Product safety
Please note the following hazard warnings:
Hazard pictograms
Signal word
Warning
Hazard warnings
May cause an allergic skin reaction.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Very toxic to aquatic life with long lasting effects.
Flammable liquid and vapour.
Dispose of contents/container to …
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
Take off contaminated clothing and wash before reuse.
IF ON SKIN:
In case of inadequate ventilation wear respiratory protection.
Wear protective gloves/protective clothing/eye protection/face protection.
Avoid release to the environment.
Use only outdoors or in a well-ventilated area.
Keep cool.
Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
Read label before use.
Keep out of reach of children.
If medical advice is needed, have product container or label at hand.
Repeated exposure may cause skin dryness or cracking.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Very toxic to aquatic life with long lasting effects.
Flammable liquid and vapour.
Dispose of contents/container to …
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
Take off contaminated clothing and wash before reuse.
IF ON SKIN:
In case of inadequate ventilation wear respiratory protection.
Wear protective gloves/protective clothing/eye protection/face protection.
Avoid release to the environment.
Use only outdoors or in a well-ventilated area.
Keep cool.
Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
Read label before use.
Keep out of reach of children.
If medical advice is needed, have product container or label at hand.
Repeated exposure may cause skin dryness or cracking.
H317, H335, H336, H410, H226, P501, P304+P340, P303+P361+P353, P362, P302, P285, P280, P273, P271, P235, P210, P103, P102, P101, EUH066
Documents
Datasheet
PDF, 127,88 KB
Safety datasheet
PDF, 170,66 KB
Safety datasheet
PDF, 183,49 KB
Safety datasheet
PDF, 181,61 KB
Safety datasheet
PDF, 176,40 KB
Accessories
-23%
SEATEC
EPOTEC Epoxy Primer
€29.37
from
€22
65
2 variants
-24%
SEATEC
PLASMOTEC One-Component Underwater Primer
€20.97
from
€15
92
2 variants
YACHTCARE
Dust Cloth
only
€3
78
> 100
3M
Premium Respirator Mask
only
€7
52
33
3M
Safety Goggles
only
€11
72
26
3M
Protective Overall
from
€13
40
4 variants
3M
Masking Tape TOP TAPE 18 mm or 24 mm x 50 m
from
€2
48
2 variants
Antifouling Flat Brush
from
€2
10
3 variants
Paint Set / Roller, Handle and Tray
only
€2
61
> 100
-27%
SEATEC
Antifouling Thinner
€18.45
only
€13
40
> 100
Customers also bought
TIKAL
TIKALFLEX Contact 12 Adhesive / Sealant
from
€5
84
5 variants
-26%
SEATEC
STANDARD PRO Self-Polishing Antifouling
€28.53
from
€20
97
8 variants
-27%
SEATEC
Antifouling Thinner
€18.45
only
€13
40
> 100
-23%
SEATEC
EPOTEC Epoxy Primer
€29.37
from
€22
65
2 variants
-22%
SEATEC
Epoxy Putty
€26.85
from
€20
97
2 variants
-24%
SEATEC
PLASMOTEC One-Component Underwater Primer
€20.97
from
€15
92
2 variants
Similar items
NEW
INTERNATIONAL
TRILUX 200 Hard Antifouling
€63.00
from
€58
78
6 variants
NEW
SEAJET
COASTAL 037 Hard Antifouling
€32.73
from
€26
01
10 variants
-56%
BOERO
SCIROCCO 622 PLUS Hard Antifouling
€85.75
from
€37
77
5 variants
-58%
BOERO
ALTURA 619 PLUS Hard Antifouling
€112.89
only
€47
02
6
HEMPEL
ECOPOWER RACING Hard Antifouling
only
€70
55
2
-17%
SEATEC
GTI 30 Thin-Film Antifouling / graphite
€40.29
from
€33
57
2 variants
-42%
INTERNATIONAL
ULTRA 300 Hard Antifouling
€82.94
from
€47
86
14 variants
HEMPEL
HARD RACING Antifouling with TecCel
from
€32
73
10 variants
-50%
INTERNATIONAL
VC OFFSHORE EU Hard Antifouling
€96.56
from
€47
86
7 variants
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .
Technical question
Question:
Karlis B.
asked
on Jan 7, 2019
Hello, last year I use SEATEC - Antifouling STANDARD PRO, can I paint over SPRINT PRO? That is recumended tehnology for good adhesion?
Answer:
Dear Karlis, please use our -24217- for one coat between the both antifoulings.
Your SVB-team.
Question:
Anton M.
asked
on Nov 16, 2022
Aan I use SPRINT PRO Dover White on Mediterranean area for a sailing boat?
I saw an exception in the description and I didn't understand what it was referring to.
Hull material GRP
Thank you in advance.
Anton
Answers:
Dear Anton, Sprint Pro - Dover White isn´t effectevily for the Mediterranean area. (so like every Dover White antifouling). Please choose another Colour for this. Your SVB-team.
Dear Sven,
Thank you for your answer.
I don't want to insist wrongly, but could you give me more details. what are the risks or in what sense it is not good
Best regards,
Anton
Question:
Henri K.
asked
on Mar 13, 2023
Hello
I have a question about SVB SPRINT PRO Hard Antifouling paint (https://www.svb24.com/en/seatec-sprint-pro-hard-antifouling.html). Is this paint compatible with TEAMAC PROTECTOR II (https://www.teamac.co.uk/products/category/antifouling/protector)?
Last season I used TEAMAC PROTECTOR, but I would like to try SVB SPRINT PRO as lots of people are recommending it. Can I paint TEAMAC over with SPRINT PRO?
Answer:
Dear customer, unfortunately we are not familar with the Teamac series, but generally you should use our art. # 24217 to coat between layers in this case. Thanks.