Transform your manual marine toilet into a convenient electric toilet. This conversion kit is suitable for most marine toilets with 4-hole mounting. Available for 12V and 24V DC.
Transform your manual marine toilet into a convenient electric toilet. This conversion kit is suitable for most marine toilets with 4-hole mounting (PAR / JABSCO, RM 69, TMC, Splash). Available for 12V and 24V DC.
Length from front edge to rear edge: 370 mm.
Hole size base/bowl: 67 mm
Hole size base/floor: 144 mm
Screw hole Ø (base / floor): 9 mm
Screw hole Ø (base / WC): 5 mm
Diameter of the base is 170 mm
The width of the rear cover is 100 mm
The cable has a length of approx. 230 mm.
4-hole mounting: bolt circle 95 mm, hole spacing opposite 100 mm.
Hose length: 400 mm
Power consumption: 12 V / 13 A / 24 V / 7 A
Hose connection inlet: ¾ "/ outlet: 1" or 1½ "
Suction height: 1.2 m, self-priming
Drainage height: 5 m
We recommend a 25 A fuse for the 12 V on-board WC and a 12 A fuse for the 24 V on-board WC.
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: firstname.lastname@example.org or by phone on: +49 (0)421 57290510 .
More "Customers ask customers" available in the following languages
When you change the pump from manual to electric, the inlet and outlet tubes are the same, although of different sizes. The water inlet pipe has an arrow indicating the direction of water flow indicated on the pump. The outlet tube you must put an adapter to get the size of the outlet tube.
On the side you cannot see on the photos there is the inlet for fresh water (saltwater). On the other side is a black hose connection where the white hose (comes with the delivery) you connect with the hose connection in the bowl for flush water. Below the black connection is a white triangular formed connection where you connect the waste hose.
I've installed the toilet. It is located aprox 2m below holding tank and 40cm above water line. I also installed a goose neck throught the inlet. When i pump all water out, by closing the inlet seacok, few hours later i find water in the toilet.
Do i need also a check valve on the outlet side?
Dear Rodrigue, is that right, that you got a goose neck only for the fresh water, but not for the waste? Please have a look at our article -30133- You need a goose neck for the waste as well. / Your SVB-team.
La prise d'eau doit être raccordée. Je dirigerais la sortie de votre pompe existante vers le kit de conversion et alimenterais l'entrée d'eau des toilettes à partir de là. J'ai connecté le kit de conversion à un système d'eau sous pression. Cela fonctionne parfaitement.
question related to OCEAN TECHNOLOGIES Toilet Conversion Kit:
the rinse water inlet to the pump from the seacock, which side of the electric motor is it?
is it on the the same side of the waste outlet or the opposite side?
I am asking this question as the flow arrow marked on the housing of the pump is confusing me.
Dear Marialberto, the flow arrow is for the dishwater. So the intake side for the dishwater is the same side like the outside for the sewer pipe. This is logical for one reason, the thru-hulls are always one the same boatside, just on different heights. Hope we could help you. Your SVB-team.
I am interested in the difference between the conversion kit for marine toilets that you offer.
76922 - price 173,21 eur
76923 - price 163,98 eur
75009 - price 204,99 eur
I think there is no any difference between the items (in operation and purpos).
Thanks for your reply.