SVB recommends the following for these items
Product details
HS stands for High Solid: There is a higher percentage of solids in the paint: "more colour - less solvent". The environment is protected, without compromises on the product performance. SUPER GLOSS HS produces less odour and is already completely opaque after 1 to 2 coats. Yield: 13.3 m²/litre. Contents: 750 ml. Various colours are available. Thinner no.1.
Processing instructions
For coated surfaces
- In good condition: Wash down with a suitable detergent, rinse with fresh water and allow to dry. Then sand the surface.
- In poor condition: Remove all previous coatings and prime the surface.
Technical Data
- Processing temperature: +10 °C to max. 35 °C
- Drying time at 15 °C: 4.5 hours
- Processing time at 15 °C: min. 36 hours
GRP
Degrease with thinner No.1 or Super Cleaner. Thoroughly sand with 180-220 grit sandpaper. Clean well and allow to dry. Prime the surface with a suitable primer, such as One Up. Then apply 1-2 coats of Super Gloss.
Weathered gelcoat
Degrease with thinner No.1 or Super Cleaner. Thoroughly sand with 180-220 grit sandpaper. Clean well and allow to dry. To avoid blistering, apply 3 coats of a 2-component primer, then overcoat with a 2-component undercoat paint. Then apply 1-2 coats of Super Gloss.
Wood / Plywood
Abrade with 80180 grade (grit) paper. Then with 280 grit paper. Remove sanding dust by brushing, dusting and wiping. Allow to dry completely before applying primer. Prime the surface with a suitable primer, such as One Up. Then apply 1-2 coats of Super Gloss.
Oily woods
Degrease the surface thoroughly. Use 80-180 grit sandpaper for sanding. Then with 280 grit paper. Remove sanding dust by brushing or dusting. Allow the surface to dry completely before applying a primer. Prime the surface with a suitable primer, such as One Up. Then apply 1-2 coats of Super Gloss.
Steel
Degrease with thinner No.1 or Super Cleaner. Gritblast to near white metal surface (Sa 2½). If gritblasting is not possible, grind the metal surface with 36-40 abrasive discs to a uniform, clean, bright well roughened metal surface (5075microns) anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry. Prime the surface with a suitable primer, such as One Up. Then apply 1-2 coats of Super Gloss.
Aluminium
Degrease with thinner No.1 or Super Cleaner. Thoroughly sand with 60-120 grit sandpaper (suitable for aluminum). Clean well and allow to dry. Prime as soon as possible (within 8 hours) with One UP. Then apply 1-2 coats of Super Gloss.
Product safety
Please note the following hazard warnings:
Harmful to aquatic life with long lasting effects.
If medical advice is needed, have product container or label at hand.
Keep out of reach of children.
Read label before use.
Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
Keep cool.
Avoid release to the environment.
Wear protective gloves/protective clothing/eye protection/face protection.
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
Dispose of contents/container to …
Documents
Datasheet
Manual
Datasheet
Datasheet
Manual
Safety datasheet
Item no.: 41161
Safety datasheet
Item no.: 41159
Safety datasheet
Item no.: 41160
Manual
Manual
Manual
Accessories
Customers also bought
Similar items
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .
- More "Customers ask customers" available in the following languages :
-
-