DSP 2024C Sine Wave Inverter and Charger / incl. DSP-EM remote control

Reset image position
Close
Back
Item no. 65607
This product is no longer available.
Available variants:
Image of DSP 1212C Sine Wave Inverter and Charger  / incl. DSP-EM remote control

DOMETIC DSP 1212C Sine Wave Inverter and Charger / incl. DSP-EM remote control

SinePower DSP-C devices are an innovative combination of charger and inverter in a compact and lightweight design. The Intelligent circuit technology and practical DSP-EM remote control allows them to be independent from the external 230 V AC grid and provide...

Image of DSP 1224C Sine Wave Inverter and Charger  / incl. DSP-EM remote control

DOMETIC DSP 1224C Sine Wave Inverter and Charger / incl. DSP-EM remote control

SinePower DSP-C devices are an innovative combination of charger and inverter in a compact and lightweight design. The Intelligent circuit technology and practical DSP-EM remote control allows them to be independent from the external 230 V AC grid and provide...

Product details

The SinePower DSP-C devices provide maximum independence from the external AC power supply. With their innovative combination of charger and inverter in a compact and lightweight design, they support all kinds of vehicle supply thanks to an innovative energy management system.
The devices operate as either 230 V sine wave inverters or battery chargers with a 4-stage IU charging characteristic, or in power sharing mode, they can supply power to 230 V devices and charge the battery at the same time. In generator mode (mains voltage function), it supports the 230 V on-board power supply with energy from the battery if the mains voltage supply is insufficient.
An integrated mains priority circuit with voltage synchronization ensures a smooth switch over between mains and inverter power. If the external 230 V grid fails completely, the inverter switches on immediately, generates a pure sinusoidal 230 or 240 V alternating voltage from the 24 V battery power and supplies the connected devices with it.
A maximum output of 2000 W is available and enables coffee machines, microwaves and many more devices to be operated trouble-free.
When no 230 V power supply is required, an intelligent standby mode saves energy while maintaining full flexibility and configuration capability.
A temperature and load-controlled fan provides noise-reduced cooling. Integrated protection prevents damage from overloading, overheating, over and under-voltage. The practical DSP-EM remote control (incl. connection cable) is used to control, configure and display basic functions and important parameters. Compatible with EURO6 vehicles and CI/LIN bus.

Options
  • Possible operating modes
    • 230 V sine wave inverter with mains priority switch and Softstart for devices with high initial currents
    • Battery charger with 4-stage IUOU charging characteristics, suitable for charging lead / acid, gel, AGM and lithium batteries (LiFePO4 DOMETIC eStore)
    • Power sharing, powers connected 230 V devices while charging a battery
    • Generator (mains voltage) function, the device provides support for a low-fused external 230-V mains voltage with energy from the battery. Battery voltage is converted and added to the 230V mains power.
  • Intended for use in vehicle TN networks.
    In this case, connect the neutral conductor of the AC output to the vehicle ground, an earth leakage circuit breaker MUST be installed on the AC output of the device.
Assembly instructions for DC connection
Keep cables as short as possible (<1 m) and use copper cables with the following minimum cross-sections.

Device
Required
Cable Cross Section
Required
Fuse
DSP2024C 25 mm² > 200A

Connecting the DSP-EM Remote Control Unit
The connection cable (supplied with the remote control) is a 7.65 m long ribbon cable (approx. 6 x 2 mm). It comes complete with RJ12 connectors (6P6C).

Technical data
DSP 1212C
Input voltage 24V
Output voltage 230 V AC / 50 Hz
240V AC / 60Hz
Operating temperature -20 to + 60 ° C
Mains priority circuit 16 A / 250 V AC
Continuous power 2000 W
Peak performance 4000 W
Max. charging current 50 A
Energy consumption 2.0 A (idling)
<0.1 A (standby)
Product dimensions 481 x 284 x 118 mm
Weight 6.6 kg


Documents

multi-flag Manual
PDF, 9,96 MB
multi-flag Manual
PDF, 3,42 MB

What other SVB customers have to say

100% real reviews
Nobody has rated this product yet

Customers ask customers

Ask other SVB customers who have already purchased this product from us about their experience.

Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .

No questions asked yet. Be the first to ask a question!