BEPMARINE 722-KS Switch Panel with LED Operation Indicator
This product is no longer available.
Product details
The BEPMARINE 722-KS switch panel is ideal for applications where a key switch is required. Delivered ready for operation and equipped with an ON / OFF switch and an LED operation indicator.
The switch panel can be used immediately as a replacement part for the following BEPMARINE products: 701-MD, 720-MD and 722, since the LED operating display is pre-wired. For these products, the NEG line of a circuit is switched on. That is, the switch contacts BAT and IGN are located in the NEG line. To do this, the red wire for the LED operating display must be connected to a POS 12 V source.
For other applications, the key switch can, of course, also be operated with its contacts BAT and IGN in the POS line of a circuit! For this purpose, the LED operation display can be easily switched around. The wire must then be connected NEG 12 Volt.
Details:
Notes:
Not suitable for outdoor use.
By using an additional 680 - 820 Ohm / 1 W resistor in the LED connection cable, the switch panel can also be used in 24 V systems.
For LED polarity reversal, please remove the heatsink adhesive, which fixes the white plug's housing to the control panel, pull the plug, turn 180°, re-attach and fix with glue.
The switch panel can be used immediately as a replacement part for the following BEPMARINE products: 701-MD, 720-MD and 722, since the LED operating display is pre-wired. For these products, the NEG line of a circuit is switched on. That is, the switch contacts BAT and IGN are located in the NEG line. To do this, the red wire for the LED operating display must be connected to a POS 12 V source.
For other applications, the key switch can, of course, also be operated with its contacts BAT and IGN in the POS line of a circuit! For this purpose, the LED operation display can be easily switched around. The wire must then be connected NEG 12 Volt.
Details:
- Scope of delivery: Key switch with 12 volt LED operation indicator on plastic panel, 2 keys
- Panel dimensions (LxWxD): 70 x 70 x 76 mm
- Mounting: 4 holes of 6 mm (1/4 "), hole spacing 54 mm
- Required mounting hole: Ø 38 mm
- Switch connections: Screw mounting for 4 mm ring cable shoes
- LED connector: Plug
- LED operating voltage: 12 volts
- LED current consumption: Approx. 15 mA @ 12 V
- Maximum load capacity: BEPMARINE does not provide any details.
Notes:
Not suitable for outdoor use.
By using an additional 680 - 820 Ohm / 1 W resistor in the LED connection cable, the switch panel can also be used in 24 V systems.
For LED polarity reversal, please remove the heatsink adhesive, which fixes the white plug's housing to the control panel, pull the plug, turn 180°, re-attach and fix with glue.
Documents
Short manual
PDF, 382,72 KB
Similar items
SEATEC
Spare Key for Battery Switch
only
€1
64
> 100
BEPMARINE
Battery Management Panel 800-MS3
only
€1.478
95
1
NEW
SEATEC
High-Load Battery Shut-Off Switch / 600A
only
€29
37
7
NEW
SEATEC
High-Load Battery Selector Switch / 600A / 12V
only
€25
17
12
NEW
SEATEC
High-load Toggle Switch ON/OFF
only
€25
17
74
NEW
SEATEC
Battery Switch with Key / M10
only
€8
36
67
NEW
SEATEC
Battery Switch, 275 A
only
€13
40
NEW
SEATEC
Battery Pole Terminal with Circuit Breaker
only
€8
36
> 100
PHILIPPI
TSA 265 Remote Controlled Main Switch / 24 V
only
€179
79
2
PHILIPPI
TSA 265 Remote Controlled Main Switch / 12 V
only
€179
79
1
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .
No questions asked yet. Be the first to ask a question!