AUTOTERM FLOW 5D Diesel Water Heater / 12 V / 5 kW
Article Number
42952
Description
AUTOTERM AIR - FLOW 5D diesel liquid heater
Fuel
Diesel
Operating voltage
12 V
Heating capacity (continuous operation)
5
kW
Max. flow rate
20
l/min
Power consumption
42
W
Fuel consumption
0.7
l/h
Boost function
No
Number of outputs
1
Inlet-Ø
18
mm
Outlet-Ø
18 mm
Exhaust-Ø
24 mm
Length
22
cm
Width
90
mm
Height
13.6
cm
Weight
8
kg
Product details
The FLOW 5D compact diesel liquid heater from Autoterm features an impressive heating output of 5 kW and can be used in combination with heat exchangers, boilers and radiators. It can also be used pre-heat the vehicle engine and compartment. The cold start function guarantees engine starting at low temperatures (down to -45°C), which also increases the service life of your engine. Can be operated with the engine switched on or off. Supplied with installation kit and control panel.
Water heater advantages
Standby mode
In standby mode, the heater shuts off when a settable temperature threshold is exceeded and the pump continues to operate. The value can be set between 20 and 95° C. If required, the pump run can also be deactivated in standby mode.
Including control panel
Delivery includes virtually everything that is needed for basic installation. The Comfort Control display panel boasts a modern design and numerous functions, such as three adjustable timers, extended heating modes, fan functions and much more. The intelligent thermostat function, for example, automatically switches the heating on when the temperature falls below a set number and similarly turns it off once a set temperature is reached. Multifunctional rotary knob with grippy rubber coating and OLED display. Small installation dimensions, easy to use, stylish design.
Additional switching inputs
The wiring harness features a gate input for connecting your own remote control or other secondary control unit. This requires only two cables to be connected via switch or relay.
E-mark
All Autoterm heaters have an E-mark (e2) and can therefore be installed without registration.
Technical data
Included in delivery
Water heater advantages
- Excellent heat distribution
- High level of efficiency with correct insulation
- Pleasant radiating heat (no dry air as is the case with warm air heaters)
- Automatic heating
- Cost-effective operation
- Optional radiators can be individually adjusted
Standby mode
In standby mode, the heater shuts off when a settable temperature threshold is exceeded and the pump continues to operate. The value can be set between 20 and 95° C. If required, the pump run can also be deactivated in standby mode.
Including control panel
Delivery includes virtually everything that is needed for basic installation. The Comfort Control display panel boasts a modern design and numerous functions, such as three adjustable timers, extended heating modes, fan functions and much more. The intelligent thermostat function, for example, automatically switches the heating on when the temperature falls below a set number and similarly turns it off once a set temperature is reached. Multifunctional rotary knob with grippy rubber coating and OLED display. Small installation dimensions, easy to use, stylish design.
Additional switching inputs
The wiring harness features a gate input for connecting your own remote control or other secondary control unit. This requires only two cables to be connected via switch or relay.
E-mark
All Autoterm heaters have an E-mark (e2) and can therefore be installed without registration.
Technical data
Voltage | 12 V (10- 16 V) |
Heating capacity | 5 kW |
Fuel | Diesel |
Fuel consumption | 0.7 l/h |
Circulation rate | 1200 l/h @ 0 bar 800 l/h @ 0.18 bar |
Power consumption | Normal: 42 W Start phase 122 W (100 s) |
Connection diameter | 18 mm |
Dimensions (h x w x d) | 220 x 90 x 136 mm |
Weight: | 8 kg |
Included in delivery
- 12 V heater
- "Comfort Control" panel
- Dosing pump "Thomas Magnet P327"
- Dosing pump rubber holder
- Dosing pump wire harness
- Heater wire harness
- Intake air hose with silencer
- Exhaust silencer
- 6 m fuel line
- 1 m corrugated metal exhaust pipe
- "Bosch PAD 12 V" liquid pump
- Water hose with preformed bends for installation
- Water hose connectors, T
- Screws, nuts, brackets, heat shrink tubing, cable ties
- Documentation
Accessories
-5%
Heavy-Duty Stainless Steel Hose Clamps
€4.88
from
€4
62
24 variants
WEBASTO
Heat exchanger with heater fan MADERA 4D
only
€198
19
2
-5%
WEBASTO
Heat exchanger with heater fan MADERA 8D
€301.00
only
€285
67
2
Stainless Steel Hose Clamps
from
€1
76
18 variants
Boiler / Cooling Water Hose / DIN73411-B
from
€8
36
4 variants
Cooling Water Hose - Heavy Duty
from
€21
81
9 variants
Similar items
-9%
WEBASTO
Thermo Top Pro 120 Water Heater / 24 V / 12 kW
€1,989.00
only
€1.815
08
-9%
WEBASTO
Thermo Top Pro 120 Water Heater / 12 V / 12 kW
€1,989.00
only
€1.815
08
-9%
WEBASTO
THERMO PRO 90 Marine Diesel Water Heater / 24 V / 9.1 kW
€2,419.00
only
€2.201
64
1
-9%
WEBASTO
Thermo Top Pro 90 Marine Water Heater / 12 V / 9.1 kW
€2,379.00
only
€2.168
03
1
Customers ask customers
Ask other SVB customers who have already purchased this product from us about their experience.
Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .
No questions asked yet. Be the first to ask a question!