FOX-062 Miniature Charge Controller / PWM / 6 A

Reset image position
Close
Back
Item no. 20205
This product is no longer available. But a successive product is available:
Available variants:
Image of FOX-062 Miniature Charge Controller / PWM / 6.6 A

SUNWARE FOX-062 Miniature Charge Controller / PWM / 6.6 A

The FOX-062 is a highly modern miniature-charge regulator for 12 V and 24 V solar systems. Even though it is small in size, the overcharge protection is designed for a solar current of 6.6 A. This corresponds to 120 Wp max. solar power at 12 V or 240 Wp at 24...

Product details

The FOX-062 is a highly modern miniature-charge regulator for 12 V and 24 V solar systems. Even though it is small in size, the overcharge protection is designed for a solar current of 6 A. This corresponds to 100 Wp max. solar power at 12 V or 200 Wp at 24 V. Reverse current protection is integrated.
The charging characteristic can be set for lead-acid, GEL, LiFePO4 or AGM batteries using the red DIP switch in the controller housing. The opening can be closed with a slide, making accidental change and dirt entry impossible.
A protective SureSeal socket is located on the input end, into which a SureSeal plug can be inserted. On the output end towards the batteries, there is a car plug connector with integrated safety. When the red adapter is switched off, the car connector can also be used.
Delivery includes 1m cable 2x1.5 mm² with SureSeal plug on one end, This allows each module to be directly connected to the charge controller.
Note: Modules with a maximum output of 100 Wp can be connected to this charge controller in a 12 V on-board network. In a 24 V on-board network, the maximum module output must not exceed 200 Wp.

Technical Data
  • 12 V / 24 V system voltage
  • 6 A max. solar power (lsc)
  • 100 watts solar power at 12 V
  • 200 watts solar power at 24 V
  • Suitable module voltages for 12V systems:
    • Open circuit voltage Uoc > 16V and < 24V
    • Voltage at maximum power Ump > 14V and < 20V
  • Suitable module voltages for 24V systems:
    • Open circuit voltage Uoc > 32V and < 48V
    • Voltage at maximum power Ump > 28V and < 40V
  • Battery type adjustable via DIP switch to lead-acid, AGM, gel or LiFePO4 batteries
  • Charging voltage
    • Lead acid 14.4 V
    • AGM 14.5 V
    • Gel 14.3 V
    • LiFePO4 14.6 V
    • Trickle charge 13.8 V
  • Multi-colour LED indicator

High charging efficiency
This charge controller is designed as a series controller with active reverse current protection. A charging degree effectiveness of 98% is achieved. In contrast to MPPT regulators, this regulator type has a up to 20% higher charging performance while using 12 V or 24 V solar modules. High converter losses are fully avoided.
This series controller really stands out in very low lighting; in a normal MPPT regulator, losses would strongly influence the flow rate.
Since the FOX - 062 has no leakage, no cooler is necessary. Der beste Beweis für optimales Layout der Schaltung.

Automatic 12 V / 24 V recognition
After plugging in the controller, the controller checks the current battery voltage and thereby determines the system voltage of the battery. No settings need to be made for this.
The controller will not start if the battery voltage is less than 8.6 V for safety reasons, as the battery may be defective.

LED display
The FOX-062 is equipped with a three-colour LED. A variety of information regarding the battery and charge can be presented by combining the LED colours and adjusting the light duration or flashing frequency:
  • Flashing red: battery empty (< 20 %)
  • Constant red: battery low (< 30 %)
  • Orange: battery normal (30% - 70 %)
  • Constant green: battery normal (> 70 %)
  • Flashing green: battery full (100 %)

When charging current is flowing from the solar module into the battery, the LED flickers briefly every few seconds. If the plug is pulled out of the socket, the LED goes off - even if a solar module is connected.

Made in Germany!
All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed.

On request, extension cables with SureSeal plug and socket are available in 5 or 10 m lengths.

Documents

en-flag Datasheet
PDF, 444,52 KB
de-flag Datasheet
PDF, 498,56 KB
de-flag Drawing
.PDF, 17,04 KB
Item no.: 20205
multi-flag Manual
PDF, 1,32 MB

What other SVB customers have to say

100% real reviews

4 customer reviews

4 (out of 4 ratings)
2 Stars
(0)
1 Stars
(0)
100% recommend SVB
Thorsten K.
by Thorsten K. Flag of Germany 8/7/2023 Verified purchase
Works flawlessly
Good quality
Thomas J.
by Thomas J. Flag of Germany 8/9/2021 Verified purchase
Works flawlessly.
Ralph H.
by Ralph H. Flag of Germany 4/20/2019 Verified purchase
SUNWARE FOX-062
Everything was great, price and delivery and return service, all very well; The part itself OK, but unfortunately not suitable for my "electronics" contaminated car. Customer service and reversal was perfect.

Customers ask customers

Ask other SVB customers who have already purchased this product from us about their experience.

Your question will be automatically forwarded to other SVB customers and published on the product page. Please do not ask any questions which can only be answered by the SVB team – such as the status of an order or product availability. You are also more than welcome to contact our SVB team by email at: info@svb24.com or by phone on: +49 (0)421 57290510 .

  • More "Customers ask customers" available in the following languages :
  • Flag of Français
  • Flag of Deutsch
No questions asked yet. Be the first to ask a question!